Latest revision as of 16:16, 20 June 2021
Information about message (contribute ) This message has no documentation.
If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (RGB-Pi JAMMA Installation )
JAMMA / MVS ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓ ┃GND A┃1 GND┃ ┃GND B┃2 GND┃ ┃+5V C┃3 +5v┃ ┃+5v D┃4 +5v┃ ┃ E┃5 ┃ ┃+12v F┃6 +12v┃ ┃Key H┃7 Key┃ ┃ J┃8 ┃ ┃ K┃9 ┃ ┃Speaker - or L L┃10 Speaker + or R┃ ┃ M┃11 ┃ ┃Video GREEN N┃12 VideoRED┃ ┃Video SYNC P┃13 VideoBLUE┃ ┃P2 Button 7 R┃14 VideoGND┃ ┃ S┃15 Button7 P1┃ ┃P2 Coin T┃16 Coin P1┃ ┃P2 Start U┃17 Start P1┃ ┃P2 Up V┃18 Up P1┃ ┃P2 Down W┃19 Down P1┃ ┃P2 Left X┃20 Left P1┃ ┃P2 Right Y┃21 Right P1┃ ┃P2 Button1 Z┃22 Button1 P1┃ ┃P2 Button2 a┃23 Button2 P1┃ ┃P2 Button3 b┃24 Button3 P1┃ ┃P2 Button4 c┃25 Button4 P1┃ ┃P2 Button5 d┃26 Button5 P1┃ ┃GND/P2 Button6 e┃27 Button6 P1/GND┃ ┃GND f┃28 GND┃ ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛ *Pins 10 & L change depending on the position of the stereo/mono switch. For mono use + - and for stereo use R & L and common ground. *Pins 27 & e are connected to GND by default. To enable the same as the 6th button, cut the jumpers JP1 & JP2 on the board.
JAMMA / MVS
┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
┃GND A┃1 GND┃
┃GND B┃2 GND┃
┃+5V C┃3 +5v┃
┃+5v D┃4 +5v┃
┃ E┃5 ┃
┃+12v F┃6 +12v┃
┃Key H┃7 Key┃
┃ J┃8 ┃
┃ K┃9 ┃
┃Speaker - or L L┃10 Speaker + or R┃
┃ M┃11 ┃
┃Video GREEN N┃12 VideoRED┃
┃Video SYNC P┃13 VideoBLUE┃
┃P2 Button 7 R┃14 VideoGND┃
┃ S┃15 Button7 P1┃
┃P2 Coin T┃16 Coin P1┃
┃P2 Start U┃17 Start P1┃
┃P2 Up V┃18 Up P1┃
┃P2 Down W┃19 Down P1┃
┃P2 Left X┃20 Left P1┃
┃P2 Right Y┃21 Right P1┃
┃P2 Button1 Z┃22 Button1 P1┃
┃P2 Button2 a┃23 Button2 P1┃
┃P2 Button3 b┃24 Button3 P1┃
┃P2 Button4 c┃25 Button4 P1┃
┃P2 Button5 d┃26 Button5 P1┃
┃GND/P2 Button6 e┃27 Button6 P1/GND┃
┃GND f┃28 GND┃
┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
*Pins 10 & L change depending on the position of the stereo/mono switch. For mono use + - and for stereo use R & L and common ground.
*Pins 27 & e are connected to GND by default. To enable the same as the 6th button, cut the jumpers JP1 & JP2 on the board.
Translation JAMMA / MVS ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓ ┃GND A┃1 GND┃ ┃GND B┃2 GND┃ ┃+5V C┃3 +5v┃ ┃+5v D┃4 +5v┃ ┃ E┃5 ┃ ┃+12v F┃6 +12v┃ ┃Key H┃7 Key┃ ┃ J┃8 ┃ ┃ K┃9 ┃ ┃Speaker - or L L┃10 Speaker + or R┃ ┃ M┃11 ┃ ┃Video GREEN N┃12 VideoRED┃ ┃Video SYNC P┃13 VideoBLUE┃ ┃P2 Button 7 R┃14 VideoGND┃ ┃ S┃15 Button7 P1┃ ┃P2 Coin T┃16 Coin P1┃ ┃P2 Start U┃17 Start P1┃ ┃P2 Up V┃18 Up P1┃ ┃P2 Down W┃19 Down P1┃ ┃P2 Left X┃20 Left P1┃ ┃P2 Right Y┃21 Right P1┃ ┃P2 Button1 Z┃22 Button1 P1┃ ┃P2 Button2 a┃23 Button2 P1┃ ┃P2 Button3 b┃24 Button3 P1┃ ┃P2 Button4 c┃25 Button4 P1┃ ┃P2 Button5 d┃26 Button5 P1┃ ┃GND/P2 Button6 e┃27 Button6 P1/GND┃ ┃GND f┃28 GND┃ ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛ *Pins 10 & L change depending on the position of the stereo/mono switch. For mono use + - and for stereo use R & L and common ground. *Pins 27 & e are connected to GND by default. To enable the same as the 6th button, cut the jumpers JP1 & JP2 on the board. JAMMA / MVS
┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
┃GND A┃1 GND┃
┃GND B┃2 GND┃
┃+5V C┃3 +5v┃
┃+5v D┃4 +5v┃
┃ E┃5 ┃
┃+12v F┃6 +12v┃
┃Key H┃7 Key┃
┃ J┃8 ┃
┃ K┃9 ┃
┃Speaker - or L L┃10 Speaker + or R┃
┃ M┃11 ┃
┃Video GREEN N┃12 VideoRED┃
┃Video SYNC P┃13 VideoBLUE┃
┃P2 Button 7 R┃14 VideoGND┃
┃ S┃15 Button7 P1┃
┃P2 Coin T┃16 Coin P1┃
┃P2 Start U┃17 Start P1┃
┃P2 Up V┃18 Up P1┃
┃P2 Down W┃19 Down P1┃
┃P2 Left X┃20 Left P1┃
┃P2 Right Y┃21 Right P1┃
┃P2 Button1 Z┃22 Button1 P1┃
┃P2 Button2 a┃23 Button2 P1┃
┃P2 Button3 b┃24 Button3 P1┃
┃P2 Button4 c┃25 Button4 P1┃
┃P2 Button5 d┃26 Button5 P1┃
┃GND/P2 Button6 e┃27 Button6 P1/GND┃
┃GND f┃28 GND┃
┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
*Pins 10 & L change depending on the position of the stereo/mono switch. For mono use + - and for stereo use R & L and common ground.
*Pins 27 & e are connected to GND by default. To enable the same as the 6th button, cut the jumpers JP1 & JP2 on the board.