RGB-Pi JAMMA Installation

From RGB-Pi Wiki
Revision as of 19:58, 30 July 2019 by ATG (talk | contribs) (Created page with "Available in English and Spanish / *Disponible en Ingles y Español* '''JAMMA RGB-Pi Pinout''' ┏━━━━━━━━━━━━━━━━┳━━━━━━...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

Available in English and Spanish / *Disponible en Ingles y Español*

JAMMA RGB-Pi Pinout

   ┏━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
   ┃GND            A┃1             GND┃
   ┃GND            B┃2             GND┃
   ┃+5V            C┃3             +5v┃
   ┃+5v            D┃4             +5v┃
   ┃               E┃5                ┃
   ┃+12v           F┃6            +12v┃
   ┃Key            H┃7             Key┃
   ┃               J┃8                ┃
   ┃               K┃9                ┃
   ┃Speaker -/L    L┃10    Speaker +/R┃
   ┃P1 Button7     M┃11               ┃
   ┃Video GREEN    N┃12       VideoRED┃
   ┃Video SYNC     P┃13      VideoBLUE┃
   ┃P2 Button 7    R┃14       VideoGND┃
   ┃P2 Button 8    S┃15     Button8 P1┃
   ┃P2 Coin        T┃16        Coin P1┃
   ┃P2 Start       U┃17       Start P1┃
   ┃P2 Up          V┃18          Up P1┃
   ┃P2 Down        W┃19        Down P1┃
   ┃P2 Left        X┃20        Left P1┃
   ┃P2 Right       Y┃21       Right P1┃
   ┃P2 Button1     Z┃22     Button1 P1┃
   ┃P2 Button2     a┃23     Button2 P1┃
   ┃P2 Button3     b┃24     Button3 P1┃
   ┃P2 Button4     c┃25     Button4 P1┃
   ┃P2 Button5     d┃26     Button5 P1┃
   ┃P2 Button6     e┃27     Button6 P1┃
   ┃GND            f┃28            GND┃
   ┗━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
   

JAMMA RGB-Pi installation instructions

Steps:
1. DON'T SKIP THIS STEP, Put one of the ┳ pieces in pin 7 of the jamma harness
2. WITHOUT THE PCB CONNECTED turn on the machine and adjust the voltage in pin 3 to 5.25v
3. Plug the pcb into the raspberry with the jamma connector facing out
4. Put a heatsink on the golden part indicated with the heat symbol
5. Download the latest version of the operating system from rgb-pi.com
6. Format one 8GB or biggest microSD in Fat32
7. Download Etcher from etcher.io to record the image in the SD
8. Record the image WITHOUT DECOMPRESSING in the SD and EXTRACT WITH SAFETY
9. Put the SD in the Pi and connect the jamma plate WITH THE MACHINE OFF

JAMMA RGB-Pi instrucciones de instalación

Pasos:
1. NO SALTARSE ESTE PASO, Ponga una de las piezas ┳ en el pin 7 del conector jamma
2. SIN EL PCB CONECTADO encienda la maquina y ajuste la tension en el pin 3 a 5.25v
3. Conecte el pcb en la raspberry con el conector jamma hacia afuera
4. Poner un disipador por la parte dorada indicada con el símbolo de calor
5. Descargar la última versión del sistema operativo desde rgb-pi.com
6. Formatear una microSD de 8GB o superior en Fat32
7. Descargar Etcher de etcher.io para grabar la imagen en la SD
8. Grabar la imagen SIN DESCOMPRIMIR en la SD y EXTRAER CON SEGURIDAD
9. Poner la SD en la Pi y conectar la placa jamma CON LA MÁQUINA APAGADA