Difference between revisions of "RGB-Pi JAMMA Installation"

From RGB-Pi Wiki
Jump to: navigation, search
(38 intermediate revisions by 2 users not shown)
Line 1: Line 1:
Available in English and Spanish / *Disponible en Ingles y Español*
+
'''Steps'''
  
'''JAMMA RGB-Pi Pinout'''
+
{|
 +
|-
 +
|1. '''DO NOT SKIP THIS STEP'''. Insert the ┳ piece in pin 7 of the female JAMMA harness
 +
[[File:T.png|320px|border]][[File:Tjamma.png|320px|border]]
 +
|-
 +
|2. With the RGB-Pi board still '''DISCONNECTED''', turn on the cabinet and adjust the voltage in pin 3 to 5.25v.
 +
[[File:tester.png|320px|border]]
 +
|-
 +
|3. '''Check if your machine has a coin counter or electronic purse''' on pin 16 & T, if this pin gives 12v or 5v this '''can damage the rgb-pi board''', disconnect the power of the coin purse or counter or replace it with a button or put a relay.
 +
[[File:relay2.png|320px|border]]
 +
|-
 +
|4. Connect the RGB-Pi board to the Raspberry with the JAMMA connector facing to the outside of the Raspberry Pi
 +
[[File:jamma0.png|320px|border]][[File:jamma1.png|320px|border]]
 +
|-
 +
|5. If you are going to use a high volume level, you must add a heatsink like the used for the CPU of the Pi in the golden square indicated with the heat symbol, if your volume level is low and you do not notice heating in this square or you are using it [https://www.thingiverse.com/thing:3804116 a cooling system with fan ]does not need to be used.
 +
[[File:fan.png|320px|border]]
 +
|-
 +
|6. '''WITH THE MACHINE OFF''' connect the JAMMA RGB-Pi to the arcade cabinet. '''DO NOT PLUG ANY USB POWER ADAPTER TO THE RASPBERRY PI'''
 +
[[File:recom2.png|320px|border]]
 +
|-
 +
|7. That's all! For instructions on how to install RGB-Pi OS, please visit the corresponding section in [[OS_Installation|this wiki]].
 +
|}
 +
 
 +
'''JAMMA RGB-Pi Pinout Serie4'''
  
 +
    JAMMA / MVS
 
     ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
 
     ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
 
     ┃GND            A┃1            GND┃
 
     ┃GND            A┃1            GND┃
Line 13: Line 37:
 
     ┃                J┃8                ┃
 
     ┃                J┃8                ┃
 
     ┃                K┃9                ┃
 
     ┃                K┃9                ┃
     ┃Speaker -/L     L┃10   Speaker +/R┃
+
     ┃Speaker - or L L┃10 Speaker + or R┃
     ┃P1 Button7      M┃11              ┃
+
     ┃                M┃11              ┃
 
     ┃Video GREEN    N┃12      VideoRED┃
 
     ┃Video GREEN    N┃12      VideoRED┃
 
     ┃Video SYNC      P┃13      VideoBLUE┃
 
     ┃Video SYNC      P┃13      VideoBLUE┃
 
     ┃P2 Button 7    R┃14      VideoGND┃
 
     ┃P2 Button 7    R┃14      VideoGND┃
     ┃P2 Button 8    S┃15    Button8 P1┃
+
     ┃                S┃15    Button7 P1┃
 
     ┃P2 Coin        T┃16        Coin P1┃
 
     ┃P2 Coin        T┃16        Coin P1┃
 
     ┃P2 Start        U┃17      Start P1┃
 
     ┃P2 Start        U┃17      Start P1┃
Line 30: Line 54:
 
     ┃P2 Button4      c┃25    Button4 P1┃
 
     ┃P2 Button4      c┃25    Button4 P1┃
 
     ┃P2 Button5      d┃26    Button5 P1┃
 
     ┃P2 Button5      d┃26    Button5 P1┃
     ┃P2 Button6     e┃27     Button6 P1┃
+
     ┃GND/P2 Button6 e┃27 Button6 P1/GND┃
 
     ┃GND            f┃28            GND┃
 
     ┃GND            f┃28            GND┃
 
     ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
 
     ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
     On board extra buttons
+
     *Pins 10 & L change depending on the position of the stereo/mono switch. For mono use + - and for stereo use R & L and common ground.
 +
    *Pins 27 & e are connected to GND by default. To enable the same as the 6th button, cut the jumpers JP1 & JP2 on the board.
 +
 
 +
    Kick
 
     ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
 
     ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
     ┃P2 Button9  P2B9┃P1B9  Button9 P1┃
+
     ┃P2 Button4      4┃6      Button6 P1┃
     ┃P2 Button10 P2B10┃P1B10 Button10 P1┃
+
     ┃P2 Button5      5┃5      Button5 P1┃
 +
    ┃P2 Button6      6┃4      Button4 P1┃
 
     ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
 
     ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
      
+
     *Take the ground from any pin of the harness
'''JAMMA RGB-Pi installation instructions'''
 
 
 
{|
 
|Steps:
 
|-
 
|1. DON'T SKIP THIS STEP, Put one of the ┳ pieces in pin 7 of the jamma harness
 
|-
 
|2. WITHOUT THE PCB CONNECTED turn on the machine and adjust the voltage in pin 3 to 5.25v
 
|-
 
|3. Plug the pcb into the raspberry with the jamma connector facing out
 
|-
 
|4. Put a heatsink on the golden part indicated with the heat symbol
 
|-
 
|5. Download the latest version of the operating system from rgb-pi.com
 
|-
 
|6. Format one 8GB or biggest microSD in Fat32
 
|-
 
|7. Download Etcher from etcher.io to record the image in the SD
 
|-
 
|8. Record the image WITHOUT DECOMPRESSING in the SD and EXTRACT WITH SAFETY
 
|-
 
|9. Put the SD in the Pi and connect the jamma plate WITH THE MACHINE OFF
 
|-
 
|}
 
 
 
---------------------------------------------------------------------------------------------------------
 
 
 
'''JAMMA RGB-Pi instrucciones de instalación'''
 
 
 
{|
 
|Pasos:
 
|-
 
|1. NO SALTARSE ESTE PASO, Ponga una de las piezas ┳ en el pin 7 del conector jamma
 
|-
 
|2. SIN EL PCB CONECTADO encienda la maquina y ajuste la tension en el pin 3 a 5.25v
 
|-
 
|3. Conecte el pcb en la raspberry con el conector jamma hacia afuera
 
|-
 
|4. Poner un disipador por la parte dorada indicada con el símbolo de calor
 
|-
 
|5. Descargar la última versión del sistema operativo desde rgb-pi.com
 
|-
 
|6. Formatear una microSD de 8GB o superior en Fat32
 
|-
 
|7. Descargar Etcher de etcher.io para grabar la imagen en la SD
 
|-
 
|8. Grabar la imagen SIN DESCOMPRIMIR en la SD y EXTRAER CON SEGURIDAD
 
|-
 
|9. Poner la SD en la Pi y conectar la placa jamma CON LA MÁQUINA APAGADA
 
|-
 
|}
 

Revision as of 10:01, 23 September 2020

Steps

1. DO NOT SKIP THIS STEP. Insert the ┳ piece in pin 7 of the female JAMMA harness

T.pngTjamma.png

2. With the RGB-Pi board still DISCONNECTED, turn on the cabinet and adjust the voltage in pin 3 to 5.25v.

Tester.png

3. Check if your machine has a coin counter or electronic purse on pin 16 & T, if this pin gives 12v or 5v this can damage the rgb-pi board, disconnect the power of the coin purse or counter or replace it with a button or put a relay.

Relay2.png

4. Connect the RGB-Pi board to the Raspberry with the JAMMA connector facing to the outside of the Raspberry Pi

Jamma0.pngJamma1.png

5. If you are going to use a high volume level, you must add a heatsink like the used for the CPU of the Pi in the golden square indicated with the heat symbol, if your volume level is low and you do not notice heating in this square or you are using it a cooling system with fan does not need to be used.

Fan.png

6. WITH THE MACHINE OFF connect the JAMMA RGB-Pi to the arcade cabinet. DO NOT PLUG ANY USB POWER ADAPTER TO THE RASPBERRY PI

Recom2.png

7. That's all! For instructions on how to install RGB-Pi OS, please visit the corresponding section in this wiki.

JAMMA RGB-Pi Pinout Serie4

   JAMMA / MVS
   ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
   ┃GND             A┃1             GND┃
   ┃GND             B┃2             GND┃
   ┃+5V             C┃3             +5v┃
   ┃+5v             D┃4             +5v┃
   ┃                E┃5                ┃
   ┃+12v            F┃6            +12v┃
   ┃Key             H┃7             Key┃
   ┃                J┃8                ┃
   ┃                K┃9                ┃
   ┃Speaker - or L  L┃10 Speaker + or R┃
   ┃                M┃11               ┃
   ┃Video GREEN     N┃12       VideoRED┃
   ┃Video SYNC      P┃13      VideoBLUE┃
   ┃P2 Button 7     R┃14       VideoGND┃
   ┃                S┃15     Button7 P1┃
   ┃P2 Coin         T┃16        Coin P1┃
   ┃P2 Start        U┃17       Start P1┃
   ┃P2 Up           V┃18          Up P1┃
   ┃P2 Down         W┃19        Down P1┃
   ┃P2 Left         X┃20        Left P1┃
   ┃P2 Right        Y┃21       Right P1┃
   ┃P2 Button1      Z┃22     Button1 P1┃
   ┃P2 Button2      a┃23     Button2 P1┃
   ┃P2 Button3      b┃24     Button3 P1┃
   ┃P2 Button4      c┃25     Button4 P1┃
   ┃P2 Button5      d┃26     Button5 P1┃
   ┃GND/P2 Button6  e┃27 Button6 P1/GND┃
   ┃GND             f┃28            GND┃
   ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
   *Pins 10 & L change depending on the position of the stereo/mono switch. For mono use + - and for stereo use R & L and common ground.
   *Pins 27 & e are connected to GND by default. To enable the same as the 6th button, cut the jumpers JP1 & JP2 on the board.
   Kick
   ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
   ┃P2 Button4      4┃6      Button6 P1┃
   ┃P2 Button5      5┃5      Button5 P1┃
   ┃P2 Button6      6┃4      Button4 P1┃
   ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
   *Take the ground from any pin of the harness