Difference between revisions of "RGB-Pi JAMMA Installation"
(Created page with "Available in English and Spanish / *Disponible en Ingles y Español* '''JAMMA RGB-Pi Pinout''' ┏━━━━━━━━━━━━━━━━┳━━━━━━...") |
|||
(17 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
Available in English and Spanish / *Disponible en Ingles y Español* | Available in English and Spanish / *Disponible en Ingles y Español* | ||
− | ' | + | [[File:Key.png|400px|thumb|DON'T SKIP THIS STEP, put on 7 and press hard]] |
− | + | '''JAMMA RGB-Pi Pinout Serie4''' | |
− | ┃GND | + | |
− | ┃GND | + | JAMMA / MVS |
− | ┃+5V | + | ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓ |
− | ┃+5v | + | ┃GND A┃1 GND┃ |
− | ┃ | + | ┃GND B┃2 GND┃ |
− | ┃+12v | + | ┃+5V C┃3 +5v┃ |
− | ┃Key | + | ┃+5v D┃4 +5v┃ |
− | ┃ | + | ┃ E┃5 ┃ |
− | ┃ | + | ┃+12v F┃6 +12v┃ |
− | ┃Speaker - | + | ┃Key H┃7 Key┃ |
− | ┃P1 Button7 | + | ┃ J┃8 ┃ |
− | ┃Video GREEN | + | ┃ K┃9 ┃ |
− | ┃Video SYNC | + | ┃Speaker - or L L┃10 Speaker + or R┃ |
− | ┃P2 Button 7 | + | ┃P1 Button7 M┃11 ┃ |
− | + | ┃Video GREEN N┃12 VideoRED┃ | |
− | ┃P2 Coin | + | ┃Video SYNC P┃13 VideoBLUE┃ |
− | ┃P2 Start | + | ┃P2 Button 7 R┃14 VideoGND┃ |
− | ┃P2 Up | + | ┃ S┃15 Button7 P1┃ |
− | ┃P2 Down | + | ┃P2 Coin T┃16 Coin P1┃ |
− | ┃P2 Left | + | ┃P2 Start U┃17 Start P1┃ |
− | ┃P2 Right | + | ┃P2 Up V┃18 Up P1┃ |
− | ┃P2 Button1 | + | ┃P2 Down W┃19 Down P1┃ |
− | ┃P2 Button2 | + | ┃P2 Left X┃20 Left P1┃ |
− | ┃P2 Button3 | + | ┃P2 Right Y┃21 Right P1┃ |
− | ┃P2 Button4 | + | ┃P2 Button1 Z┃22 Button1 P1┃ |
− | ┃P2 Button5 | + | ┃P2 Button2 a┃23 Button2 P1┃ |
− | + | ┃P2 Button3 b┃24 Button3 P1┃ | |
− | ┃GND | + | ┃P2 Button4 c┃25 Button4 P1┃ |
− | + | ┃P2 Button5 d┃26 Button5 P1┃ | |
+ | ┃GND/P2 Button6 e┃27 Button6 P1/GND┃ | ||
+ | ┃GND f┃28 GND┃ | ||
+ | ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛ | ||
+ | *Pins 10 & L changes depend the switch for stereo or mono output, mono use + - indications and stereo use R & L and common ground. | ||
+ | *Pins 27 & e are plugged to GND by defaut to enable the sixth button cut the jumpers JP1 & JP2 on the board. | ||
+ | *Los pines 10 y L cambian dependiendo de la posición del switch si está en mono o estéreo, para mono usar las indicaciones + - y para estéreo R y L y una masa común. | ||
+ | *Los pines 27 y e están conectados a masa por defecto, para habilitarlos como botón sexto bot'on corte los jumpers JP1 y JP2 en la placa. | ||
+ | |||
+ | Kick | ||
+ | ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓ | ||
+ | ┃P2 Button4 4┃6 Button6 P1┃ | ||
+ | ┃P2 Button5 5┃5 Button5 P1┃ | ||
+ | ┃P2 Button6 6┃4 Button4 P1┃ | ||
+ | ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛ | ||
+ | *Take the ground from any pin of the harness | ||
+ | *Coger la masa de cualquier otro pin del jamma. | ||
'''JAMMA RGB-Pi installation instructions''' | '''JAMMA RGB-Pi installation instructions''' | ||
Line 39: | Line 55: | ||
|Steps: | |Steps: | ||
|- | |- | ||
− | |1. DON'T SKIP THIS STEP, Put one of the ┳ pieces in pin 7 of the jamma harness | + | |1. DON'T SKIP THIS STEP, Put one of the ┳ pieces in pin 7 of the female jamma harness |
+ | |- | ||
+ | |2. WITHOUT THE RGB-Pi CONNECTED turn on the machine and adjust the voltage in pin 3 to 5.25v | ||
|- | |- | ||
− | | | + | |3. If you have an electronic coin purse, check that it does not send voltage through the pin 16 or T, mechanical coin purse skip this step. |
|- | |- | ||
− | | | + | |4. Plug the RGB-Pi into the raspberry with the jamma connector facing out |
|- | |- | ||
− | | | + | |5. Put a heatsink on the golden part indicated with the heat (same model as for Pi) |
|- | |- | ||
− | | | + | |6. Download the latest version of the operating system from rgb-pi.com |
|- | |- | ||
− | | | + | |7. Format one 8GB or biggest microSD in Fat32 |
|- | |- | ||
− | | | + | |8. Download Etcher from etcher.io to record the image in the SD |
|- | |- | ||
− | | | + | |9. Record the image WITHOUT DECOMPRESSING in the SD and EXTRACT WITH SAFETY from PC |
|- | |- | ||
− | | | + | |10. Put the SD in the Pi and connect the jamma plate WITH THE MACHINE and WITHOUT POWERING THE Pi BY THE MICRO USB |
|- | |- | ||
|} | |} | ||
Line 66: | Line 84: | ||
|Pasos: | |Pasos: | ||
|- | |- | ||
− | |1. NO SALTARSE ESTE PASO, Ponga una de las piezas ┳ en el pin 7 del conector jamma | + | |1. NO SALTARSE ESTE PASO, Ponga una de las piezas ┳ en el pin 7 del conector jamma hembra |
+ | |- | ||
+ | |2. SIN EL RGB-Pi CONECTADO encienda la maquina y ajuste la tension en el pin 3 a 5.25v | ||
|- | |- | ||
− | | | + | |3. Si tienes monedero electrónico compruebe que no envía voltaje por el pin 16 y T, monederos mecánicos saltarse este paso. |
|- | |- | ||
− | | | + | |4. Conecte el RGB-Pi en la Raspberry con el conector jamma hacia afuera |
|- | |- | ||
− | | | + | |5. Poner un disipador por la parte dorada indicada con el símbolo de calor (mismo modelo que para la Pi) |
|- | |- | ||
− | | | + | |6. Descargar la última versión del sistema operativo desde rgb-pi.com |
|- | |- | ||
− | | | + | |7. Formatear una microSD de 8GB o superior en Fat32 |
|- | |- | ||
− | | | + | |8. Descargar Etcher de etcher.io para grabar la imagen en la SD |
|- | |- | ||
− | | | + | |9. Grabar la imagen SIN DESCOMPRIMIR en la SD y EXTRAER CON SEGURIDAD del PC |
|- | |- | ||
− | | | + | |10. Poner la SD en la Pi y conectar la placa jamma CON LA MÁQUINA APAGADA y SIN ALIMENTAR LA Pi POR EL MICRO USB |
|- | |- | ||
|} | |} |
Revision as of 19:17, 23 March 2020
Available in English and Spanish / *Disponible en Ingles y Español*
JAMMA RGB-Pi Pinout Serie4
JAMMA / MVS ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓ ┃GND A┃1 GND┃ ┃GND B┃2 GND┃ ┃+5V C┃3 +5v┃ ┃+5v D┃4 +5v┃ ┃ E┃5 ┃ ┃+12v F┃6 +12v┃ ┃Key H┃7 Key┃ ┃ J┃8 ┃ ┃ K┃9 ┃ ┃Speaker - or L L┃10 Speaker + or R┃ ┃P1 Button7 M┃11 ┃ ┃Video GREEN N┃12 VideoRED┃ ┃Video SYNC P┃13 VideoBLUE┃ ┃P2 Button 7 R┃14 VideoGND┃ ┃ S┃15 Button7 P1┃ ┃P2 Coin T┃16 Coin P1┃ ┃P2 Start U┃17 Start P1┃ ┃P2 Up V┃18 Up P1┃ ┃P2 Down W┃19 Down P1┃ ┃P2 Left X┃20 Left P1┃ ┃P2 Right Y┃21 Right P1┃ ┃P2 Button1 Z┃22 Button1 P1┃ ┃P2 Button2 a┃23 Button2 P1┃ ┃P2 Button3 b┃24 Button3 P1┃ ┃P2 Button4 c┃25 Button4 P1┃ ┃P2 Button5 d┃26 Button5 P1┃ ┃GND/P2 Button6 e┃27 Button6 P1/GND┃ ┃GND f┃28 GND┃ ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛ *Pins 10 & L changes depend the switch for stereo or mono output, mono use + - indications and stereo use R & L and common ground. *Pins 27 & e are plugged to GND by defaut to enable the sixth button cut the jumpers JP1 & JP2 on the board. *Los pines 10 y L cambian dependiendo de la posición del switch si está en mono o estéreo, para mono usar las indicaciones + - y para estéreo R y L y una masa común. *Los pines 27 y e están conectados a masa por defecto, para habilitarlos como botón sexto bot'on corte los jumpers JP1 y JP2 en la placa.
Kick ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓ ┃P2 Button4 4┃6 Button6 P1┃ ┃P2 Button5 5┃5 Button5 P1┃ ┃P2 Button6 6┃4 Button4 P1┃ ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛ *Take the ground from any pin of the harness *Coger la masa de cualquier otro pin del jamma.
JAMMA RGB-Pi installation instructions
Steps: |
1. DON'T SKIP THIS STEP, Put one of the ┳ pieces in pin 7 of the female jamma harness |
2. WITHOUT THE RGB-Pi CONNECTED turn on the machine and adjust the voltage in pin 3 to 5.25v |
3. If you have an electronic coin purse, check that it does not send voltage through the pin 16 or T, mechanical coin purse skip this step. |
4. Plug the RGB-Pi into the raspberry with the jamma connector facing out |
5. Put a heatsink on the golden part indicated with the heat (same model as for Pi) |
6. Download the latest version of the operating system from rgb-pi.com |
7. Format one 8GB or biggest microSD in Fat32 |
8. Download Etcher from etcher.io to record the image in the SD |
9. Record the image WITHOUT DECOMPRESSING in the SD and EXTRACT WITH SAFETY from PC |
10. Put the SD in the Pi and connect the jamma plate WITH THE MACHINE and WITHOUT POWERING THE Pi BY THE MICRO USB |
JAMMA RGB-Pi instrucciones de instalación
Pasos: |
1. NO SALTARSE ESTE PASO, Ponga una de las piezas ┳ en el pin 7 del conector jamma hembra |
2. SIN EL RGB-Pi CONECTADO encienda la maquina y ajuste la tension en el pin 3 a 5.25v |
3. Si tienes monedero electrónico compruebe que no envía voltaje por el pin 16 y T, monederos mecánicos saltarse este paso. |
4. Conecte el RGB-Pi en la Raspberry con el conector jamma hacia afuera |
5. Poner un disipador por la parte dorada indicada con el símbolo de calor (mismo modelo que para la Pi) |
6. Descargar la última versión del sistema operativo desde rgb-pi.com |
7. Formatear una microSD de 8GB o superior en Fat32 |
8. Descargar Etcher de etcher.io para grabar la imagen en la SD |
9. Grabar la imagen SIN DESCOMPRIMIR en la SD y EXTRAER CON SEGURIDAD del PC |
10. Poner la SD en la Pi y conectar la placa jamma CON LA MÁQUINA APAGADA y SIN ALIMENTAR LA Pi POR EL MICRO USB |