Difference between revisions of "RGB-Pi JAMMA Installation"
m (Protected "Instrucciones de instalación Jamma" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))) |
|||
| Line 31: | Line 31: | ||
┃P2 Button4 c┃25 Button4 P1┃ | ┃P2 Button4 c┃25 Button4 P1┃ | ||
┃P2 Button5 d┃26 Button5 P1┃ | ┃P2 Button5 d┃26 Button5 P1┃ | ||
| − | + | ┃GND/P2 Button6 e┃27 Button6 P1/GND┃ | |
┃GND f┃28 GND┃ | ┃GND f┃28 GND┃ | ||
┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛ | ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛ | ||
| − | + | Kick | |
┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓ | ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓ | ||
| − | ┃P2 | + | ┃P2 Button5 P2B5┃P1B5 Button5 P1┃ |
| − | ┃P2 | + | ┃P2 Button6 P2B6┃P1B6 Button6 P1┃ |
┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛ | ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛ | ||
| Line 49: | Line 49: | ||
|2. WITHOUT THE PCB CONNECTED turn on the machine and adjust the voltage in pin 3 to 5.25v | |2. WITHOUT THE PCB CONNECTED turn on the machine and adjust the voltage in pin 3 to 5.25v | ||
|- | |- | ||
| − | |3. | + | |3. With the machine on, check that none of the buttons send voltage to the board. |
|- | |- | ||
| − | |4. | + | |4. Plug the pcb into the raspberry with the jamma connector facing out |
|- | |- | ||
| − | |5. | + | |5. Put a heatsink on the golden part indicated with the heat symbol |
|- | |- | ||
| − | |6. | + | |6. Download the latest version of the operating system from rgb-pi.com |
|- | |- | ||
| − | |7. | + | |7. Format one 8GB or biggest microSD in Fat32 |
|- | |- | ||
| − | |8. | + | |8. Download Etcher from etcher.io to record the image in the SD |
|- | |- | ||
| − | |9. Put the SD in the Pi and connect the jamma plate WITH THE MACHINE OFF | + | |9. Record the image WITHOUT DECOMPRESSING in the SD and EXTRACT WITH SAFETY |
| + | |- | ||
| + | |10. Put the SD in the Pi and connect the jamma plate WITH THE MACHINE OFF | ||
|- | |- | ||
|} | |} | ||
| Line 76: | Line 78: | ||
|2. SIN EL PCB CONECTADO encienda la maquina y ajuste la tension en el pin 3 a 5.25v | |2. SIN EL PCB CONECTADO encienda la maquina y ajuste la tension en el pin 3 a 5.25v | ||
|- | |- | ||
| − | |3. Conecte el pcb en la raspberry con el conector jamma hacia afuera | + | |3. Con la maquina encendida compruebe que ninguno de los botones envía voltaje a la placa. |
| + | |- | ||
| + | |4. Conecte el pcb en la raspberry con el conector jamma hacia afuera | ||
|- | |- | ||
| − | | | + | |5. Poner un disipador por la parte dorada indicada con el símbolo de calor |
|- | |- | ||
| − | | | + | |6. Descargar la última versión del sistema operativo desde rgb-pi.com |
|- | |- | ||
| − | | | + | |7. Formatear una microSD de 8GB o superior en Fat32 |
|- | |- | ||
| − | | | + | |8. Descargar Etcher de etcher.io para grabar la imagen en la SD |
|- | |- | ||
| − | | | + | |9. Grabar la imagen SIN DESCOMPRIMIR en la SD y EXTRAER CON SEGURIDAD |
|- | |- | ||
| − | | | + | |10. Poner la SD en la Pi y conectar la placa jamma CON LA MÁQUINA APAGADA |
|- | |- | ||
|} | |} | ||
Revision as of 14:24, 18 September 2019
Available in English and Spanish / *Disponible en Ingles y Español*
JAMMA RGB-Pi Pinout
JAMMA / MVS ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓ ┃GND A┃1 GND┃ ┃GND B┃2 GND┃ ┃+5V C┃3 +5v┃ ┃+5v D┃4 +5v┃ ┃ E┃5 ┃ ┃+12v F┃6 +12v┃ ┃Key H┃7 Key┃ ┃ J┃8 ┃ ┃ K┃9 ┃ ┃Speaker -/L L┃10 Speaker +/R┃ ┃P1 Button7 M┃11 ┃ ┃Video GREEN N┃12 VideoRED┃ ┃Video SYNC P┃13 VideoBLUE┃ ┃P2 Button 7 R┃14 VideoGND┃ ┃P2 Button 8 S┃15 Button8 P1┃ ┃P2 Coin T┃16 Coin P1┃ ┃P2 Start U┃17 Start P1┃ ┃P2 Up V┃18 Up P1┃ ┃P2 Down W┃19 Down P1┃ ┃P2 Left X┃20 Left P1┃ ┃P2 Right Y┃21 Right P1┃ ┃P2 Button1 Z┃22 Button1 P1┃ ┃P2 Button2 a┃23 Button2 P1┃ ┃P2 Button3 b┃24 Button3 P1┃ ┃P2 Button4 c┃25 Button4 P1┃ ┃P2 Button5 d┃26 Button5 P1┃ ┃GND/P2 Button6 e┃27 Button6 P1/GND┃ ┃GND f┃28 GND┃ ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛ Kick ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓ ┃P2 Button5 P2B5┃P1B5 Button5 P1┃ ┃P2 Button6 P2B6┃P1B6 Button6 P1┃ ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
JAMMA RGB-Pi installation instructions
| Steps: |
| 1. DON'T SKIP THIS STEP, Put one of the ┳ pieces in pin 7 of the jamma harness |
| 2. WITHOUT THE PCB CONNECTED turn on the machine and adjust the voltage in pin 3 to 5.25v |
| 3. With the machine on, check that none of the buttons send voltage to the board. |
| 4. Plug the pcb into the raspberry with the jamma connector facing out |
| 5. Put a heatsink on the golden part indicated with the heat symbol |
| 6. Download the latest version of the operating system from rgb-pi.com |
| 7. Format one 8GB or biggest microSD in Fat32 |
| 8. Download Etcher from etcher.io to record the image in the SD |
| 9. Record the image WITHOUT DECOMPRESSING in the SD and EXTRACT WITH SAFETY |
| 10. Put the SD in the Pi and connect the jamma plate WITH THE MACHINE OFF |
JAMMA RGB-Pi instrucciones de instalación
| Pasos: |
| 1. NO SALTARSE ESTE PASO, Ponga una de las piezas ┳ en el pin 7 del conector jamma |
| 2. SIN EL PCB CONECTADO encienda la maquina y ajuste la tension en el pin 3 a 5.25v |
| 3. Con la maquina encendida compruebe que ninguno de los botones envía voltaje a la placa. |
| 4. Conecte el pcb en la raspberry con el conector jamma hacia afuera |
| 5. Poner un disipador por la parte dorada indicada con el símbolo de calor |
| 6. Descargar la última versión del sistema operativo desde rgb-pi.com |
| 7. Formatear una microSD de 8GB o superior en Fat32 |
| 8. Descargar Etcher de etcher.io para grabar la imagen en la SD |
| 9. Grabar la imagen SIN DESCOMPRIMIR en la SD y EXTRAER CON SEGURIDAD |
| 10. Poner la SD en la Pi y conectar la placa jamma CON LA MÁQUINA APAGADA |
