Difference between revisions of "RGB-Pi JAMMA Installation"

From RGB-Pi Wiki
Jump to: navigation, search
m
m
Line 23: Line 23:
 
|9. Burn the image '''WITHOUT DECOMPRESSING''' to the SD card and perform a '''SAFE EXTRACTION'''
 
|9. Burn the image '''WITHOUT DECOMPRESSING''' to the SD card and perform a '''SAFE EXTRACTION'''
 
|-
 
|-
|10. You can now plug the SD into the Raspberry Pi and connect the JAMMA connector to the arcade cabinet. '''DO NOT PLUG ANY USB POWER ADAPTER TO RASPBERRY PI'''
+
|10. You can now plug the SD into the Raspberry Pi and connect the JAMMA connector to the arcade cabinet. '''DO NOT PLUG ANY USB POWER ADAPTER TO THE RASPBERRY PI'''
 
|-
 
|-
 
|}
 
|}
Line 60: Line 60:
 
     ┃GND            f┃28            GND┃
 
     ┃GND            f┃28            GND┃
 
     ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
 
     ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
     *Pins 10 & L changes depend the switch for stereo or mono output, mono use + - indications and stereo use R & L and common ground.
+
     *Pins 10 & L change depending on the position of the stereo/mono switch. For mono use + - and for stereo use R & L and any ground.
     *Pins 27 & e are plugged to GND by defaut to enable the sixth button cut the jumpers JP1 & JP2 on the board.
+
     *Pins 27 & e are connected to GND by default. To enable the same as the 6th button, cut the jumpers JP1 & JP2 on the board.
    *Los pines 10 y L cambian dependiendo de la posición del switch si está en mono o estéreo, para mono usar las indicaciones + - y para estéreo R y L y una masa común.
 
    *Los pines 27 y e están conectados a masa por defecto, para habilitarlos como botón sexto bot'on corte los jumpers JP1 y JP2 en la placa.
 
  
 
     Kick
 
     Kick
Line 72: Line 70:
 
     ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
 
     ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
 
     *Take the ground from any pin of the harness
 
     *Take the ground from any pin of the harness
    *Coger la masa de cualquier otro pin del jamma.
 

Revision as of 20:35, 26 April 2020

DON'T SKIP THIS STEP, put on 7 and press hard

Steps

1. DO NOT SKIP THIS STEP. Insert the ┳ piece in pin 7 of the female JAMMA harness
2. With the RGB-Pi board still DISCONNECTED, turn on the cabinet and adjust the voltage in pin 3 to 5.25v
3. If you have an electronic coin acceptor, check that it is not sending any voltage through the pin 16 or T (mechanical coin acceptor users can skip this step)
4. Connect the RGB-Pi board to the Raspberry with the JAMMA connector facing to the outside of the Raspberry Pi
5. Put a heatsink on the golden part indicated with the heat symbol (you can use regular Raspberry heatsinks)
6. Download the latest version of the RGB-Pi OS from rgb-pi.com
7. Grab any 8GB or greater MicroSD card (all content will be deleted)
8. Download Etcher from etcher.io to write the image to the SD
9. Burn the image WITHOUT DECOMPRESSING to the SD card and perform a SAFE EXTRACTION
10. You can now plug the SD into the Raspberry Pi and connect the JAMMA connector to the arcade cabinet. DO NOT PLUG ANY USB POWER ADAPTER TO THE RASPBERRY PI

JAMMA RGB-Pi Pinout Serie4

   JAMMA / MVS
   ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
   ┃GND             A┃1             GND┃
   ┃GND             B┃2             GND┃
   ┃+5V             C┃3             +5v┃
   ┃+5v             D┃4             +5v┃
   ┃                E┃5                ┃
   ┃+12v            F┃6            +12v┃
   ┃Key             H┃7             Key┃
   ┃                J┃8                ┃
   ┃                K┃9                ┃
   ┃Speaker - or L  L┃10 Speaker + or R┃
   ┃P1 Button7      M┃11               ┃
   ┃Video GREEN     N┃12       VideoRED┃
   ┃Video SYNC      P┃13      VideoBLUE┃
   ┃P2 Button 7     R┃14       VideoGND┃
   ┃                S┃15     Button7 P1┃
   ┃P2 Coin         T┃16        Coin P1┃
   ┃P2 Start        U┃17       Start P1┃
   ┃P2 Up           V┃18          Up P1┃
   ┃P2 Down         W┃19        Down P1┃
   ┃P2 Left         X┃20        Left P1┃
   ┃P2 Right        Y┃21       Right P1┃
   ┃P2 Button1      Z┃22     Button1 P1┃
   ┃P2 Button2      a┃23     Button2 P1┃
   ┃P2 Button3      b┃24     Button3 P1┃
   ┃P2 Button4      c┃25     Button4 P1┃
   ┃P2 Button5      d┃26     Button5 P1┃
   ┃GND/P2 Button6  e┃27 Button6 P1/GND┃
   ┃GND             f┃28            GND┃
   ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
   *Pins 10 & L change depending on the position of the stereo/mono switch. For mono use + - and for stereo use R & L and any ground.
   *Pins 27 & e are connected to GND by default. To enable the same as the 6th button, cut the jumpers JP1 & JP2 on the board.
   Kick
   ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
   ┃P2 Button4      4┃6      Button6 P1┃
   ┃P2 Button5      5┃5      Button5 P1┃
   ┃P2 Button6      6┃4      Button4 P1┃
   ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
   *Take the ground from any pin of the harness